- Visión General
- Product Description
- Installation Instructions
- Packaging & Shipping
- Our Advantages
- Certifications
- FAQ
Información Básica.
No. de Modelo.
S-550
Aplicación
Construcción, Carpintería
Material
Silicona
Clasificación
Sala de Curación
Composición Agente Principal
Caucho
Característica
Impermeable
Composición Promotor
Agente de Curado
Composición
Material orgánico
Color
todo el color como requisito del cliente
g.w.
480g
n..
430g
peso del cartucho
60g
volumen
240ml
detalle de embalaje
24 piezas/ctn
tamaño del embalaje
30*20*24cm
piel seca
10-30 minutos
completamente seco
4 días
día fuerte máximo
después de 21 días
densidad
1.45
Paquete de Transporte
cartón
Especificación
240ml
Marca Comercial
sellador de silicona neutro para uso general c-550
Origen
China
Código del HS
3506100090
Capacidad de Producción
50000000 ctn/ año
Descripción de Producto
S-550 Wholesale General Purpose Neutral Silicone Sealant for Windows and Doors Construction Adhesive
Characteristics:
1.One component
2. Neutral Curing and non-corrosive to metal, coated glass, concrete and marble
3. Non-discoloring.
4. Excellent adhesion to glass, metal and plastic etc
5. Excellent resistance to low and high temperature, little performance changes between -40 ºC~150 ºC
6. Excellent resistance ultraviolet radiation
7. Odorless
Application:
For a wide range of Aluminum doors and windows, plastic steel doors and windows, stainless steel, glass, Aluminum sheet, ceramics, sky light, roof, most of building material. Can not use for coated glass.
Curing Time:
Track-free Time is between 15 to 20 minutes at room temperature
Completely curing Time is between 48 hours to 96 hours at room temperature.
Color available:
White, grey, black, others of special order
Way of use:
1.preparation:clean,de-grease and dry the surface.protect the edges of sealing gap with masking tape;
2.cut the nozzle according to the fissure width,cut off the tube outlet over the thread and screw the nozzle on;
3.application temperature +5c to +30c;
4.extrude silicone by means of cartridge gun;
5.tool the sealant with a wet spatula before formation occurs;
6.up to 15min, remove the masking tape;
7.fresh spots can be clean with water, after hardening mechanically only
Limitations:
1.Cannot be used as structural sealant.
2.Not compatible with materials with grease or exudation.
3.The construction surface should be clean and dry.
4.Not applicable to the seal of the immersed, airtight, or comprising substrates like copper, brass and lead, and oil-exudation surfaces.
5.Cannot be used on the substrate surface below 6ºC or above 40 ºC
Notices: 1. For best result, use opened cartridges on the same day. Otherwise store it strictly tightened
2. Pre-test is necessary to ensure the excellent adhesive property.
3. Avoid contacting with skin or eyes, in case of contacted, rinse immediately with plenty of water, go to hospital if necessary
4. Keep away from children before curing.
5. Avoid contaminating food, medicine or cosmetics.
Packaging
Cartridge: 240 ml 24 cartridges/ctn
Gross weight: 470 g Net weight: 410 g
Sausage: 780G 20 sausages/ctn
Storage and transportation:
1. 12 months stored in a dry and ventilated place below 27ºc in original packaging.
2. non-dangerous, can be transported by train, automobile, ship.
3. Uncured product may irritate eyes. In case of eyes contact, rinse them immediately with water and seek medical aid.
4. Keep out of reach of children.
TECHNICAL DATA SHEET
Testing Standard: GB/T 14683-2003
| No | Item | The standard | Test result | ||
| 1 | Appearance | Have no grain, no agglomerations, no skinning, and no bubble. | Pass the standard | ||
| 2 | Density (g/cm3) | ±0.1 | 1.438 | ||
| 3 | Droop degree mm | Uprightness | ≤3 | 0 | |
| Level | No damage | No damage | |||
| 4 | Skinning time(h) | ≤3 | 0.33 | ||
| 5 | Elastic recovery ratio (%) | ≥80 | 92 | ||
| 6 | Extrusion ability(ml/min) | ≥80 | 116 | ||
| 7 | Tensile modulus (Mpa) | 23ºC | ≤ 0.6 | 0.7 | |
| 8 | Cold-hot adhesive | No damage | No damage | ||
| 9 | Under water adhesive | No damage | No damage | ||
| 10 | UV radiation | No damage | No damage | ||
| 11 | Definite Elongation | No damage | No damage | ||
Certificate
FAQ:
1.Can u send sample to us ?
Yes, the sample is free.
2.Can you give us private design ?
Yes, we offer OEM service, can making your own brand.
3.What's your guarantee?
10-15 years.
4.Can you provide us with your client information ?
Yes, for checking our company reputation and sample collection.
5.How many days to produce one 20'container?
10-15days.
6.Can we visit factory?
Yes, warmly welcome to visit us at any time.
7.What are the documents we provide ?
Packing list, commercial invoice, CO / FORM E / FORM A , BL making according to your demand.